This automatic visual Fiber tensile screening system is made for operator skill impartial use within production and laboratory settings. Two basic model configurations permit the user to pick between a set up for regular linear Proof screening and with additional mandrels for rotary high strength screening.
The linear edition is made for production Proof testing with causes approximately 22 N. Motorized clamps with very carefully designed rubberized inserts ensure that the Optical Fiber Proof-Testing Machine is not damaged inside the screening procedure while concurrently eliminating the need for an external air provide. Levels of pulling force, pulling velocity and hold time are programmable and easily offered to the operator through the built in Liquid crystal display touch-screen manage. Data from tests can be saved and accessed using the USB port or Ethernet interface.
Mandrels of the identical design like NYFORS’ optical Fiber recoaters can easily be installed on the Proof tester within the rotary higher power settings. The Fiber is covered around the two mandrels which support it with a special clamping system. This way higher loads can be used onto the Fiber, allowing breaking power tests below managed conditions.
Changeable clamp placement facilitates testing with the greatest force amounts as well as testing of short Fiber lengths. The lightweight and light bodyweight design definitely makes the instrument easy to maneuver in a laboratory environment as well as integrate in a creation work bench where space are at reduced. The device is really a lightweight and lightweight instrument suitable for screening the potency of visual materials as much as 30 N. The equipment is created to fulfill all types of applications where a strength check has to be performed.
The equipment was created with all the consumer in mind. The FTTH Cable Production Line is easily put into the carefully guided linear clamps, and the testing begins instantly using a “One Touch” go switch. The built in microprocessor regulates all of the essential guidelines like tugging force, pulling speed and hold time. This permits to get a completely controlled test each time.
The machine can be attached to an external Computer, which enables usage of all automated parameters and settings. The device is adapted to face-alone use or the integration into various subsystems. The device has an extensive capability of signing and conserving details such as tugging force, tugging speed and Fiber diameter along with other parameters.
Two recoat injector designs can be purchased. The PTR307 utilizes a computerized water pump to inject the recoat materials. The volume of materials dispensed by the automatic injector is controlled by hand via the top-installed “Inject” button or programmed into the machine making use of the tablet pc controller. The PTR307B features a handbook recoat injection program that needs the user to personally dispense the recoat material to the mold cavity; a replacement injector for that PTR307B recoater is accessible below. Please note that this automatic injector is just suitable for higher-index recoat materials, whilst the handbook injector is compatible with each reduced- and high- directory recoat material; they are both marketed separately listed below. Make sure you get in touch with Tech Support for more information.
he handbook injector can be mounted to suitable Fiber recoaters through the 4-40 anchoring screws on the recoater real estate (see picture towards the right). Use a 3/32″ hex key to secure the injector just before use. To get in touch the PTRRRM for the recoater mold, tighten up the connector at the conclusion of the green plastic material tubes, then loosen with a 1/4 turn to permit rotation.
The injector is equipped with a distribution device and two-place choice handle for directing the stream of recoat material. A knurled dispensing screw with the inner plunger behaves as a syringe for your recoat materials. To fill up the syringe, point the handle downwards (i.e., toward the recoat container), then rotate the knurled dispensing attach counterclockwise until it spins freely to fill the syringe (demonstrated within the picture for the right). Then, to inject the recoat material to the mold, point the handle horizontally (i.e., facing qyjflh knurled screw) and rotate the screw clockwise till nearby the end of the journey range is achieved. Steer clear of bottoming out the dispenser because this may harm the interior plunger; also take care when re-interesting the threads in order to avoid cross threading the dispensing screw. Several fill/inject actions may be needed until air is displaced within the system. Use camera lens cells and an acetone or alcoholic beverages cleansing solution to collect Optical Fiber Ribbon Machine materials that flows through the mold.